Cutting Vinyl Fence to Size: A Step-by-Step Guide How to Cut Vinyl composite fence panels to Fit Shorter Sections

Comments · 449 Views

Hello, and thank you for tuning back in to the channel

Hello, and thank you for tuning back in to the channel. In today's lesson, you will learn how to cut vinyl fence. It's possible that figuring out how to cut the vinyl composite fence panels shorter section has been the most difficult challenge I've faced. This afternoon, I will demonstrate how to cut it.

So let's start often. If you are using a vinyl fence, you will eventually get to the end of it. In most cases, the corner column will intersect in this section. Because, as you can see in this particular section, it is a little bit shorter, you will need to cut it to the appropriate size in order to make it work with the tool that you require.


You can use a hand saw, a saw, or any other type of saw as long as the blade has fine teeth on it. In all honesty, I work with a craftsman vinyl blade. In addition to that, you could use some clips. To prevent the panels from moving around on the table while you cut them, you will need to keep a firm grip on them with one hand and press them down with the other. Tape is another option for protecting the vinyl record from being scratched while you work. You can determine the distance between the column of this vinyl panel kit and the goggles by using a tape measure to make the measurement. In point of fact, you are required to cut the top and bottom guide rails, and it is highly likely that you are also required to cut the panel. This is due to the fact that there is typically a gap between the panel and the column, and I will now explain what you should do.

Now, when you want to cut the vinyl composite fence panels , you need to measure from that column to that column, you need to measure from the top and bottom, okay, it's 83 inches, and then you need to measure the distance between those two columns. Therefore, the thing that you need to do is leave an inch on the top, an inch on the side, and an inch on the side to enter the interior of the column, and because of this, we will cut these bottom railings at a length of 85 inches. The top railings require the exact same treatment as the bottom ones. If they are horizontal, they ought to be identical; however, this is not a requirement; it is just a good practice. Take measurements on both sides, which should be very accurate. Because these have not been concreted and leveled, the distance between them will be approximately 83. Therefore, we cut these again. It's 85. All right, let's begin with the bottom railing, shall we?

The length is something that needs to be measured. So, let's say that there are 85 inches to the inch on each side. If you want to walk an additional half inch, that is fine with me; I want to walk 85 inches and a half. I want to leave a mark on both the underside and the surface. In the event that you do not have a ruler available to you, you can draw a line on one of the panels.


After that, it is imperative that you put on your goggles once more. You should also repeat this on the top railing so that the vinyl does not get into your eyes and cause you to miss the line. Now, it should be just right for you. Your panel needs to be installed first.

Another thing you need to watch out for is making sure the label is removed properly after you cut it off at the end of the railing. It's a good idea to put a screw in this spot so that the railing won't be able to slide in and out like that, as this will help prevent it from coming loose from the column. After you have installed all of the panels, as I mentioned before, you will typically need to cut one of them to make it fit. Because, as you can see, it's a little bit bigger than the space in between, what you need to do is measure the space in between the top and bottom right here and right here. Therefore, in order to ensure that you cut to the right when you want to cut the panel that you want, you need to make sure that you cut from the female end to the male end when you make your cut. You are going to make your cut from this side, so their method is going to be different. You need to make sure that you cut them according to the way that they are connected to one another. To do this, simply measure from the top to the inside and adjust the measurement so that the top is four.

The left side measures 4. 5 inches, while the right side measures 4. When it comes to the bottom, once you've cut it to the desired length, you can simply cover the serrated edge with a trim piece, slide it into place, and then replace the top rail. Now that you have all of the panels installed, you need to move on to installing the top rail. This is how you will cut the portion that is less long. Vinyl picket composite fence panels  ll try to keep this brief: I really do hope you find the content to be very helpful. If you truly believe this, please indicate that with a thumbs up.

If you want to see more content related to operation in the future, please do not hesitate to click the button labeled "Subscribe."I would like to thank you for watching.

Comments